Are you guys looking for Civil Engineering MCQ Questions with Answers PDF Free Download as per Civil Engineering new exam pattern? You came to the right page. This may assist you to understand and check your knowledge about the Subjects. Students also can take a free test of the Multiple Choice Questions of Civil Engineering. Each question has four options followed by the right answer. These Civil Engineering MCQ Questions are selected supported by the newest exam pattern.
Q1. Slenderness ratio of a compression member is
(A) Moment of inertia/Radius of gyration
(B) Effective length/Area of cross-section
(C) Radius of gyration/Effective length
(D) Radius of gyration/ Area of cross-section
Answer:(C) Radius of gyration/Effective length
Q2. A tension member, if subjected to possible reversal of stress due to wind, the slenderness ratio of the member should not exceed
(A) 180
(B) 200
(C) 300
(D) 350
Answer: (D) 350
Q3. If d is the distance between the flange angles, the vertical stiffeners in plate girders without horizontal stiffeners, are spaced at a distance not less than
(A) 0.15 d
(B) 0.22 d
(C) 0.33 d
(D) 0.44 d
Answer:(C) 0.33 d
Q4. The least permissible clear dimension of the web of thickness t in the panel of a plate girder, is restricted to
(A) 150 t
(B) 160 t
(C) 170 t
(D) 180 t
Answer: (D) 180 t
Q5. Pick up the correct statement from the following:
(A) Tacking rivets are used if the minimum distance between centres of two adjacent rivets exceeds 12 t or 200 mm, whichever is less
(B) Tacking rivets are not considered to calculate stress
(C) Tacking rivets are provided throughout the length of a compression member composed of two components back to back
(D) All the above
Answer: (D) All the above
Q6. Long column is one
(A) Which is more than 3 m long
(B) Whose lateral dimension is less than 25 cm
(C) Which is free at its top
(D) Which has a ratio of effective length and least lateral dimension more than 15
Answer: (D) Which has a ratio of effective length and least lateral dimension more than 15
Q7. Bearing stiffeners are provided at
(i) The supports
(ii) The mid span
(iii) The point of application of concentrated loads
The correct answer is
(A) Only (i)
(B) Both (i) and (ii)
(C) Both (i) and (iii)
(D) (i), (ii) and (iii)
Answer: (C) Both (i) and (iii)
Q8. Lug angles
(A)are used to reduce the length of connection
(B) Are unequal angles
(C) Increases shear lag
(D) All the above
Answer:(A)are used to reduce the length of connection
Q9. To minimize the total cost of a roof truss, the ratio of the cost of truss to the cost of purlins shall be
(A) 1
(B) 2
(C) 3
(D) 4
Answer: (B) 2
Q10. Web crippling generally occurs at the point where
(A) Bending moment is maximum
(B) Shearing force is minimum
(C) Concentrated loads act
(D) Deflection is maximum
Answer: (C) Concentrated loads act
Q11. The Indian standard code which deals with steel structures, is
(A) IS : 875
(B) IS : 800
(C) IS : 456
(D) IS : 1893
Answer: (B) IS : 800
Q12. When the length of a tension member is too long
(A) A wire rope is used
(B) A rod is used
(C) A bar is used
(D) A single angle is used
Answer: (C) A bar is used
Q13. Pick up the correct statement from the following:
(A) The slenderness ratio of lacing bars for compression members should not exceed 145
(B) The minimum width of lacing bar connected with rivets of nominal diameter 16 mm, is kept 50 mm
(C) The minimum thickness of a flat lacing bar is kept equal to one-fortieth of its length between inner end rivets
(D) All the above
Answer: (D) All the above
Q14. Under a concentrated load, bearing stress fb in a beam is given by (where b is the length of the bearing plate and h is the depth of the root of the fillet).
(A) fb = W/(b + h√3)tw
(B) fb = W/(b + 2h√3)tw
(C) fb = W/(b + 2h√2)tw
(D) fb = W/(b + h√2)tw
Answer:(B) fb = W/(b + 2h√3)tw
Q15. In factory buildings, the horizontal beams spanning between the wall columns supporting a wall covering, are called
(A) Stringers
(B) Trimmers
(C) Girts
(D) Lintels
Answer: (C) Girts
Design of Steel Structures Civil Engineering MCQ
- Design of Steel Structures Civil Engineering MCQ and Answers – Set 01
- Design of Steel Structures Objective Questions – Set 02
- Design of Steel Structures MCQ – Set 03
- Design of Steel Structures Multiple Choice Questions – Set 04
- MCQ on Design of Steel Structures – Set 05
- Civil Steel Structures Design Objective Questions – Set 06
- Steel Structures Civil Engineering MCQ Test – Set 07
- Steel Structures Design Multiple Choice Tests – Set 08
- Multiple Choice Questions on Steel Structure Design – Set 09
- Interview Questions on Steel Structures – Set 10
- Design of Steel Structures Interview Questions and Answers – Set 11
- Important Questions on Design of Steel Structures – Set 12
- Civil Steel Structural Engineering MCQ – Set 13
- Steel Structures Designing Multiple Choice Questions Test – Set 14
- Steel Structures Design Quiz Questions – Set 15
- Structural Steel Fabrication Interview Questions – Set 16
- Design of Steel Structures Exam Question Bank with Answers – Set 17
- Steel Structures Objective type Questions with Answers pdf – Set 18
- Civil Engineering Steel Design pdf – Set 19
- Civil Engineering Steel Structures Interview Questions – Set 20
- Design of Steel Structures Objective Questions and Answers Set – 21
We hope the given Design of Steel Structures Civil Engineering MCQ Questions with Answers will definitely yield fruitful results. Hope you got enough ideas on the MCQs on Design of Steel Structures Civil Engineering. If you have any queries related to Design of Steel Structures Civil Engineering MCQs Multiple Choice Questions with Answers, drop your questions below and will get back to you in no time.