Concrete Technology and Design Objective Type Questions SET -23

Are you guys looking for Civil Engineering MCQ Questions with Answers PDF Free Download as per Civil Engineering new exam pattern? You came to the right page. This may assist you to understand and check your knowledge about the Subjects. Students also can take a free test of the Multiple Choice Questions of Civil Engineering. Each question has four options followed by the right answer. These Civil Engineering MCQ Questions are selected supported by the newest exam pattern.

Q1. If the storey height is equal to length of RCC wall, the percentage increase in strength is

(A) 0
(B) 10
(C) 20
(D) 30

Answer: (B) 10

Q2. The effect of adding calcium chloride in concrete is
(i) To increase shrinkage
(ii) To decrease shrinkage
(iii) To increase setting time
(iv) To decrease setting time
The correct answer is

(A) (i) and (iii)
(B) (i) and (iv)
(C) (ii) and (iii)
(D) (ii) and (iv)

(B) (i) and (iv)

Q3. The process of proper and accurate measurement of concrete ingredients for uniformity of proportion, is known

(A) Grading
(B) Curing
(C) Mixing
(D) Batching

Answer:(D) Batching

Q4. For a continuous slab of 3 m × 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is

(A) 50 mm
(B) 75 mm
(C) 100 mm
(D) 120 mm

Answer: (B) 75 mm

Q5. Transport of concrete by pumps, is done for a distance of

(A) 100 m
(B) 200 m
(C) 300 m
(D) 400 m

Answer:(D) 400 m

Q6. If X, Y and Z are the fineness modulli of coarse, fine and combined aggregates, the percentage (P) of fine aggregates to combined aggregates, is

(A) P = [(Z – X)/(Z – Y)] × 100
(B) P = [(X – Z)/(Z – Y)] × 100
(C) P = [(X – Z)/(Z + Y)] × 100
(D) P = [(Z + X)/(Z – Y)] × 100

Answer: (B) P = [(X – Z)/(Z – Y)] × 100

Q7. Permissible compressive strength of M 300 concrete grade is

(A) 100 kg/cm2
(B) 150 kg/cm2
(C) 200 kg/cm2
(D) 300 kg/cm2

Answer: (D) 300 kg/cm2

Q8. The load factors for live load and dead load are taken respectively as

(A) 1.5 and 2.2
(B) 2.2 and 1.5
(C) 1.5 and 1.5
(D) 2.2 and 2.2

Answer: (B) 2.2 and 1.5

Q9. The most useless aggregate is one whose surface texture is

(A) Smooth
(B) Granular
(C) Glassy
(D) Honey combed and porous

Answer: (C) Glassy

Q10. Curing

(A) Reduces the shrinkage of concrete
(B) Preserves the properties of concrete
(C) Prevents the loss of water by evaporation
(D) All of the above

Answer: (D) All of the above

Q11. If the depth of actual neutral axis in a beam is more than the depth of critical neutral axis, then the beam is called

(A) Balanced beam
(B) Under-reinforced beam
(C) Over-reinforced beam
(D) None of the above

Answer: (C) Over-reinforced beam

Q12. Strength of concrete increases with

(A) Increase in water-cement ratio
(B) Increase in fineness of cement
(C) Decrease in curing time
(D) Decrease in size of aggregate

Answer: (B) Increase in fineness of cement

Q13. The mixture of different ingredients of cement, is burnt at

(A) 1000°C
(B) 1200°C
(C) 1400°C
(D) 1600°C

Answer: (C) 1400°C

Q14. The shrinkage of concrete

(A) Is proportional to water content is the mix
(B) Is proportional to cement concrete
(C) Increases with age of concrete
(D) All the above

Answer: (D) All the above

Q15. The datum temperature for maturity by Plowman, is

(A) 23°C
(B) 0°
(C) – 5.6°C
(D) – 11.7°C

Answer: (D) – 11.7°C

Concrete Technology and Design MCQ with Answers

We hope the given Concrete Technology and Design MCQ Questions with Answers on Civil Engineering will definitely yield fruitful results. Hope you got enough ideas on the Concrete Technology and Design MCQs on Civil Engineering. If you have any queries related to Civil Engineering MCQs Multiple Choice Questions with Answers, drop your questions below and will get back to you in no time.