# Civil Engineering Steel Structures Interview Questions – Set 20

Are you guys looking for Civil Engineering MCQ Questions with Answers PDF Free Download as per Civil Engineering new exam pattern? You came to the right page. This may assist you to understand and check your knowledge about the Subjects. Students also can take a free test of the Multiple Choice Questions of Civil Engineering. Each question has four options followed by the right answer. These Civil Engineering MCQ Questions are selected supported by the newest exam pattern.

## Q1. The range of economical spacing of trusses varies from

(A) L/3 to L/5
(B) L/4 to 2L/5
(C) L/3 to L/2
(D) 2L/5 to 3L/5, where L is span

Answer: (A) L/3 to L/5

## Q2. The allowable stress in axial tension for rolled I-sections and channels, is taken as

(A) 1420 kg/cm2
(B) 1500 kg/cm2
(C) 2125 kg/cm2
(D) 1810 kg/cm2

Answer: (B) 1500 kg/cm2

(A) 4 mm
(B) 6 mm
(C) 8 mm
(D) 10 mm

Answer: (B) 6 mm

## Q4. Effective sectional area of a compression member is:

(A) Gross sectional area – area of rivet hole
(B) Gross sectional area + area of rivet hole
(C) Gross sectional area × area of rivet hole
(D) Gross sectional area + area of rivet hole

Answer: (A) Gross sectional area – area of rivet hole

(A) 120
(B) 130
(C) 140
(D) 150

Answer: (C) 140

## Q6. The permissible stress in bending for rolled steel I-beams and channels, is

(A) 1500 kg/cm2
(B) 1575 kg/cm2
(C) 945 kg/cm2
(D) 1650 kg/cm2

Answer: (D) 1650 kg/cm2

(A) 150
(B) 180
(C) 250
(D) 350

Answer: (C) 250

## Q8. An axial loaded column is supported on a slab base whose projection is 8 cm. If the intensity of pressure from concrete is 40 kg/cm2 and allowable bending stress in slab base is 1890 kg/cm2, the thickness (t) of the slab base, is

(A) t = √(21/64)
(B) t = √(64/21)
(C) t = 21/64
(D) t = 64/21

Answer: (B) t = √(64/21)

## Q9. The distance measured along one rivet line from the centre of a rivet to the centre of adjoining rivet on an adjacent parallel rivet line, is called

(A) Pitch of rivet
(B) Gauge distance of rivet
(C) Staggered pitch
(D) All the above

Answer: (C) Staggered pitch

## Q10. In plastic analysis, the shape factor for circular sections, is

(A) 1.5
(B) 1.6
(C) 1.697
(D) None of these

Answer: (C) 1.697

## Q11. A compression member consisting of angle sections may be a

(A) Continuous member
(B) Discontinuous single angle strut
(C) Discontinuous double angle strut
(D) All the above

Answer: (D) All the above

## Q12. The effective length ‘L’ of a simply supported beam with ends restrained against torsion, and also the ends of compression flange partially restrained against lateral bending, is given by

(A) L = span
(B) L = 0.85 span
(C) L = 0.75 span
(D) L = 0.7 span

Answer: (B) L = 0.85 span

## Q13. The external wind pressure acting on a roof depends on

(A) Degree of permeability of roof
(B) Slope of roof
(C) Both (A) and (B)
(D) None of the above

Answer: (B) Slope of roof

## Q14. The main advantage of a steel member, is:

(A) Its high strength
(B) Its gas and water tightness
(C) Its long service life
(D) All the above

Answer: (D) All the above

## Q15. The permissible bearing stress in steel, is

(A) 1500 kg/cm2
(B) 1890 kg/cm2
(C) 2025 kg/cm2
(D) 2340 kg/cm2

Answer: (B) 1890 kg/cm2

## Design of Steel Structures Civil Engineering MCQ

We hope the given Design of Steel Structures Civil Engineering MCQ Questions with Answers will definitely yield fruitful results. Hope you got enough ideas on the MCQs on Design of Steel Structures Civil Engineering. If you have any queries related to Design of Steel Structures Civil Engineering MCQs Multiple Choice Questions with Answers, drop your questions below and will get back to you in no time.