Are you guys looking for Civil Engineering MCQ Questions with Answers PDF Free Download as per Civil Engineering new exam pattern? You came to the right page. This may assist you to understand and check your knowledge about the Subjects. Students also can take a free test of the Multiple Choice Questions of Civil Engineering. Each question has four options followed by the right answer. These Civil Engineering MCQ Questions are selected supported by the newest exam pattern.
Q1. Equation of motion of a point in a straight line, is
(A) v = u + ft
(B) S = ut + ½ ft2
(C) 2fS = v2 – u2
(D) All the above
Answer: (D) All the above
Q2. The angle of projection for a range is equal to the distance through which the particle would have fallen in order to acquire a velocity equal to the velocity of projection, will be
(A) 30°
(B) 45°
(C) 60°
(D) 75°
Answer: (D) 75°
Q3. Pick up the correct statement from the following:
(A) If two equal and perfectly elastic smooth spheres impinge directly, they interchange their velocities
(B) If a sphere impinges directly on an equal sphere which is at rest, then a fraction ½(1 – e2) the original kinetic energy is lost by the impact
(C) If two equal spheres which are perfectly elastic impinge at right angles, their direction after impact will still be at right angles
(D) All the above
Answer: (D) All the above
Q4. The unit of impulse, is
(A) kg.m/sec
(B) kg.m/sec
(C) kg.m/sec2
(D) kg.m/sec
Answer: (A) kg.m/sec
Q5. One half of a vibration of a body, is called
(A) Period time
(B) Oscillation
(C) Beat
(D) Amplitude
Answer: (C) Beat
Q6. The inherent property of a body which offers reluctance to change its state of rest or uniform motion, is
(A) Weight
(B) Mass
(C) Inertia
(D) Momentum
Answer: (C) Inertia
Q7. The moment of inertia of a hollow circular section whose external diameter is 8 cm and internal diameter is 6 cm, about centroidal axis, is
(A) 437.5 cm4
(B) 337.5 cm4
(C) 237.5 cm4
(D) 137.5 cm4
Answer: (D) 137.5 cm4
Q8. Time required to stop a car moving with a velocity 20 m/sec within a distance of 40 m, is
(A) 2 sec
(B) 3 sec
(C) 4 sec
(D) 5 sec
Answer:(C) 4 sec
Q9. A particle is executing simple harmonic motion in a line 1.0 m long. If the time of one complete vibration is 1 sec, then the maximum velocity of the particle is
(A) 1.00 m/sec
(B) 1.57 m/sec
(C) 3.14 m/sec
(D) 6.28 m/sec
Answer: (C) 3.14 m/sec
Q10. On a ladder resting on a rough ground and leaning against a smooth vertical wall, the force of friction acts
(A) Downwards at its upper end
(B) Upwards at its upper end
(C) Perpendicular to the wall at its upper end
(D) Zero at its upper end
Answer: (D) Zero at its upper end
Q11. A ball of mass 1 kg moving with a velocity of 2 m/sec collides a stationary ball of mass 2 kg and comes to rest after impact. The velocity of the second ball after impact will be
(A) Zero
(B) 0.5 m/sec
(C) 1.0 m/sec
(D) 2.0 m/sec
Answer:(C) 1.0 m/sec
Q12. Pick up the correct statement from the following. The kinetic energy of a body
(A) Before impact is equal to that after impact
(B) Before impact is less than that after impact
(C) Before impact is more than that after impact
(D) Remain constant
Answer: (C) Before impact is more than that after impact
Q13. A Seconds pendulum executes
(A) 0.5 beat per second
(B) 1.0 beat per second
(C) 2.0 beats per second
(D) 2.5 beats per second
Answer: (C) 2.0 beats per second
Q14. The centre of gravity of a plane lamina will not be at its geometrical centre if it is a
(A) Circle
(B) Equilateral triangle
(C) Rectangle
(D) Right angled triangle
Answer: (D) Right angled triangle
Q15. The reaction at the support ‘A’ of the beam shown in below figure is

(A) 2 t
(B) 5.8 t
(C) 0.2 t
(D) 3.5 t
Answer: (D) Right angled triangle
Applied Mechanics and Graphic Statics MCQ with Answers
- Applied Mechanics and Graphic Statics MCQ Test – Set 01
- Applied Mechanics Objective Test – Set 02
- Applied Mechanics Questions and Answers – Set 03
- Applied Mechanics Objective Questions – Set 04
- Applied Mechanics MCQ Test – Set 05
- Applied Mechanics and Graphic Statics MCQ Practice – Set 06
- Graphic Statics Exam Practice – Set 07
- Applied Mechanics MCQ Exam Questions – Set 08
- Objective Type Questions on Applied Mechanics – Set 09
- Applied Mechanics and Graphic Statics MCQ – Set 10
- Online Study Materials on Applied Mechanics – Set 11
- Online Study Materials on Graphic Statics – Set 12
- Multiple Choice Questions Civil Applied Mechanics – Set 13
- MCQ Test Applied Mechanics and Graphic Statics – Set 14
- Civil Engineering Applied Mechanics MCQ – Set 15
- Civil Engineering Graphic Statics MCQ – Set 16
- Theory Practice Applied Mechanics and Graphic Statics – Set 17
- Applied Mechanics and Graphic Statics – Set 18
- Objective Test Applied Mechanics and Graphic Statics – Set 19
- Online Test Civil Applied Mechanics and Graphic Statics – Set 20
- Civil Graphic Statics MCQ Quiz Questions – Set 21
- Online Quiz Test Applied Mechanics and Graphic Statics – Set 22
- Civil Engineering Applied Mechanics Quiz – Set 23
- Applied Mechanics and Graphic Statics Online Exam set 24
We hope the given Applied Mechanics and Graphic Statics MCQ Questions with Answers on Civil Engineering will definitely yield fruitful results. Hope you got enough ideas on the Applied Mechanics and Graphic Statics MCQs on Civil Engineering. If you have any queries related to Civil Engineering MCQs Multiple Choice Questions with Answers, drop your questions below and will get back to you in no time.