Are you guys looking for Civil Engineering MCQ Questions with Answers PDF Free Download as per Civil Engineering new exam pattern? You came to the right page. This may assist you to understand and check your knowledge about the Subjects. Students also can take a free test of the Multiple Choice Questions of Civil Engineering. Each question has four options followed by the right answer. These Civil Engineering MCQ Questions are selected supported by the newest exam pattern.
Q1. A load of 500 kg was lifted through a distance of 13 cm. by an effort of 25 kg which moved through a distance of 650 cm. The mechanical advantage of the lifting machine is
(A) 15
(B) 18
(C) 20
(D) 26
Answer: (C) 20
Q2. If the angle between the applied force and the direction of motion of a body, is between 90° and 180°, the work done, is called
(A) Virtual work
(B) Imaginary work
(C) Zero work
(D) Negative work
Answer: (D) Negative work
Q3. Three forces which act on a rigid body to keep it in equilibrium. The forces must be coplanar and
(A) Concurrent
(B) Parallel
(C) Concurrent parallel
(D) None of these
Answer: (A) Concurrent
Q4. Pick up the incorrect statement from the following. In case of suspension bridge due to rise in temperature,
(A) Dip of the cable increases
(B) Length of the cable increases
(C) Dip of the cable decreases
(D) None of these
Answer: (C) Dip of the cable decreases
Q5. If the angle of projection is double the angle of inclination (α) of the plane on which particle is projected, the ratio of times of flight up the inclined plane and down the inclined plane, will be
(A) ½ cos α
(B) ½ sin α
(C) ½ tan α
(D) 2 cos α
Answer: (A) ½ cos α
Q6. Coefficient of friction depends on
(A) Nature of surfaces only
(B) Area of contact only
(C) Both (A) and (B)
(D) None of the above
Answer: (A) Nature of surfaces only
Q7. If ‘α’ is the angular acceleration of a compound pendulum whose angular displacement is ‘θ’, the frequency of the motion is
(A) 2π √(α/θ)
(B) (1/2π) √(α/θ)
(C) 4π √(α/θ)
(D) 2π √(α – θ)
Answer: (B) (1/2π) √(α/θ)
Q8. In simple harmonic motion, acceleration of a particle is proportional to
(A) Rate of change of velocity
(B) Displacement
(C) Velocity
(D) Direction
Answer: (B) Displacement
Q9. The intrinsic equation of catenary is
(A) S = c tan ψ
(B) y = c cosh x/c
(C) y = c cosh ψ
(D) y = c sinh ψ
Answer: (A) S = c tan ψ
Q10. The acceleration of a train starting from rest at any instant is 1/6(V + 1) m/sec² where ‘V’ is the velocity of the train in m/sec. The train will attain a velocity of 36 km/hour after travelling a distance of
(A) 2000 m
(B) 2100 m
(C) 2200 m
(D) 2300 m
Answer: (D) 2300 m
Q11. When a body falls freely under gravitational force, it possesses
(A) Maximum weight
(B) Minimum weight
(C) No weight
(D) No effect on its weight
Answer: (C) No weight
Q12. If a particle is projected inside a horizontal tunnel which is 554 cm high with a velocity of 60 m per sec, the angle of projection for maximum range, is
(A) 8°
(B) 9°
(C) 10°
(D) 11°
Answer: (C) 10°
Q13. A satellite goes on moving along its orbit round the earth due to
(A) Gravitational force
(B) Centrifugal force
(C) Centripetal force
(D) None of these
Answer: (B) Centrifugal force
Q14. In a simple screw jack, the pitch of the screw is 9 mm and length of the handle operating the screw is 45 cm. The velocity ratio of the system is
(A) 1.5
(B) 5
(C) 25
(D) 314
Answer: (D) 314
Q15. What is the answer to this question?
Applied Mechanics and Graphic Statics

(A) 10.8 t
(B) 10.6 t
(C) 10.4 t
(D) 10.2 t
Answer: (A) 10.8 t
Applied Mechanics and Graphic Statics MCQ with Answers
- Applied Mechanics and Graphic Statics MCQ Test – Set 01
- Applied Mechanics Objective Test – Set 02
- Applied Mechanics Questions and Answers – Set 03
- Applied Mechanics Objective Questions – Set 04
- Applied Mechanics MCQ Test – Set 05
- Applied Mechanics and Graphic Statics MCQ Practice – Set 06
- Graphic Statics Exam Practice – Set 07
- Applied Mechanics MCQ Exam Questions – Set 08
- Objective Type Questions on Applied Mechanics – Set 09
- Applied Mechanics and Graphic Statics MCQ – Set 10
- Online Study Materials on Applied Mechanics – Set 11
- Online Study Materials on Graphic Statics – Set 12
- Multiple Choice Questions Civil Applied Mechanics – Set 13
- MCQ Test Applied Mechanics and Graphic Statics – Set 14
- Civil Engineering Applied Mechanics MCQ – Set 15
- Civil Engineering Graphic Statics MCQ – Set 16
- Theory Practice Applied Mechanics and Graphic Statics – Set 17
- Applied Mechanics and Graphic Statics – Set 18
- Objective Test Applied Mechanics and Graphic Statics – Set 19
- Online Test Civil Applied Mechanics and Graphic Statics – Set 20
- Civil Graphic Statics MCQ Quiz Questions – Set 21
- Online Quiz Test Applied Mechanics and Graphic Statics – Set 22
- Civil Engineering Applied Mechanics Quiz – Set 23
- Applied Mechanics and Graphic Statics Online Exam set 24
We hope the given Applied Mechanics and Graphic Statics MCQ Questions with Answers on Civil Engineering will definitely yield fruitful results. Hope you got enough ideas on the Applied Mechanics and Graphic Statics MCQs on Civil Engineering. If you have any queries related to Civil Engineering MCQs Multiple Choice Questions with Answers, drop your questions below and will get back to you in no time.